Skip to content

MDF Info

IT-our future!

  • Home
  • News
  • Appearance
    • The MDF industry
    • Consumption
    • Production capacity
  • Applications
    • EPF Annual Report
    • What’s New
    • The 4th European
  • MDF Outlook
    • Laminate flooring
    • Handling and Storing
    • Controlling MDF moisture content
  • Dust control

Category: News

How to Check the Ann Taylor Loft Gift Card Balance

April 11, 2022April 15, 2022 mdf-infoNews

If you’re wondering how to check the balance on your Ann Taylor Loft gift card, you’ve come to the right place. Read on for some easy instructions. This gift card can be used in store to purchase items. If you’re…

Read More→

How to Find a Trustworthy Essay Writing Service

January 13, 2022January 14, 2022 mdf-infoNews

When you are a student, finding an essay writing service can be a challenge. It can be hard to decide who is the best, and the best way to determine who is good is to read customer reviews. Many online…

Read More→

Sawing veneered MDF

September 5, 2021September 6, 2021 mdf-infoNews

For production cutting of veneered MDF, saw blades with alternate 5° face bevel and alternate 15° top bevel are recommended. In addition, a scoring saw should be used on the underside to prevent breakout. Resharpening All original angles should be…

Read More→

Polycrystalline diamond (PCD) cutters

August 27, 2021September 6, 2021 mdf-infoNews

PCD cutters are being used increasingly for large production runs. Although their initial cost is high, they outlast the corresponding carbide tooling by factors of 30 to 50 times provided they are used on controlled feed machines. Shear cutting Cutting…

Read More→

Planing and profiling MDF edges

August 20, 2021September 6, 2021 mdf-infoNews

One of the main advantages of MDF over other wood based sheet materials is the ease of shaping panels and moulding edges ready for finishing to a high appearance standard with minimum sanding and filling. Almost any profile can be…

Read More→

Resharpening

August 3, 2021September 6, 2021 mdf-infoNews

Cutters should be resharpened at appropriate intervals in order to ensure clean cut edges free from burnishing or fibre tear. Cutting and clearance angles should be maintained at each sharpening to prolong the life of the cutters. Cutters should be…

Read More→

Sawing MDF

July 24, 2021September 6, 2021 mdf-infoNews

MDF can be cut successfully with hand saws without splintering or breakout of the core fibres. Most companies will, however, use powered machines, ranging from small portable types to fully programmed panel cutting machines. As the wood raw materials for…

Read More→

Feed speed

July 17, 2021September 6, 2021 mdf-infoNews

Saw blades which have been developed for particleboard will cut MDF with reasonable success, but the adoption of alternate top bevels of 15° and an increased tip clearance angle of 20°-22° will further extend the life of the saws between…

Read More→

As the fineness of MDF

June 13, 2021September 6, 2021 mdf-infoNews

As the fineness of MDF dust puts it in a class with sander dust, special procedures may be required to maintain adequate safety standards when the amount of MDF dust represents more than 20% of the total dust load. Extraction…

Read More→

How to take a loan if you do not have an official job

May 29, 2021May 21, 2021 mdf-infoNews

According to credit policy, banks do not lend money to non-working borrowers or those employed unofficially. However, the lack of an employment document is not an insurmountable obstacle. You can get a loan without official employment in a special cash…

Read More→

Posts pagination

Previous 1 … 4 5 6 7 Next

Recent Posts

  • Прогноз цены BTC с учётом геополитических факторов
  • PEPE у 2025: чому динаміка ціни виглядає краще, ніж рік тому
  • Ethereum і DeFi у 2025: як взаємодія впливає на ціну ETH?

Categories

Archives

Categories

  • News
© 2019.mdf-info.org.All rights reserved.